Salt reading
Shows sodium chloride concentration in ppm when read with the matching salt-strip chart.
Use it to decide whether the water's salt level needs review against the generator's model-specific requirement.
Views: 0 Author: Site Editor Publish Time: 2026-11-19 Origin: Site
Salt test strips measure the sodium chloride concentration in the pool water sample, usually reported as parts per million, not the amount of active sanitizer in the water.
The AQUA CHEM product page identifies its product as Salt Test Strips, also described as Sodium Chloride Test Strips, for pools and hot tubs, and lists Total Salt (NaCl) as the measured item.
For product comparison, the same page lists a 400 to 7,000 ppm range and 10 test strips. Treat those as product and measurement-range details, not as a promise that every salt chlorine generator should operate anywhere inside the range.
A salt result answers only one question: how much salt is in the sample. It does not answer whether the water has the disinfectant level or pH balance that bathers need.
Read the color or scale value exactly as the strip instructions specify, then convert that reading to ppm with the matching chart for that strip product.
A strip range tells you what the strip can measure; your operating target comes from the salt chlorine generator model and its official instructions.
The AQUA CHEM page supports the 400 to 7,000 ppm figure as a measurement range for its salt test strips. It should not be used by itself as a universal saltwater pool target.
For a pool owner, that means a number inside the strip's readable range may still be too low, acceptable, or too high for a particular generator. For a service technician or retail counter, it means the next question is the generator model, not only the strip result.
| Number you see | What it means | What to compare it with |
|---|---|---|
| 400 to 7,000 ppm on the strip page | Measurement range for that AQUA CHEM strip product | The strip's own chart and readable scale |
| Generator salt target | Operating requirement for one generator model | The specific generator manual or control-panel guidance |
| Free chlorine, bromine, and pH values | Separate water-treatment checks | Sanitizer and pH test results, not the salt strip |
Before adding salt, compare your measured ppm with the target range in the manual or service information for the exact salt chlorine generator installed on the pool.
Do not assume a target from one generator brand, model, or control board applies to another. If the display shows low salt, high salt, or a service warning, confirm pool volume, measured ppm, and the model-specific target before adjusting salt.
Retail staff should ask for the generator model and pool volume before suggesting salt addition. Service technicians should document both the strip and generator readings because the two numbers may reflect different conditions or calibration assumptions.
If you need to inspect the generator cell or any powered pool equipment as part of a separate service task, switch off and disconnect the applicable power source before manual access, and follow only the access steps allowed by the official model manual.
A salt strip does not prove that the pool is sanitized; free chlorine or bromine and pH need their own checks.
In archived CDC newsroom guidance, CDC said swimmers can use a test strip before getting in the water and listed pH of 7.2 to 7.8, free chlorine of at least 1 ppm in pools and at least 3 ppm in hot tubs or spas, and free bromine of at least 3 ppm in pools and at least 4 ppm in hot tubs or spas.
Shows sodium chloride concentration in ppm when read with the matching salt-strip chart.
Use it to decide whether the water's salt level needs review against the generator's model-specific requirement.
Show separate water-treatment conditions such as free chlorine, bromine, and pH.
Use them to decide whether the water is ready for swimming or needs treatment before use.
When a strip result and generator display disagree, retest carefully, confirm the strip is within its readable range, and then check the generator's model-specific guidance instead of assuming either number is automatically correct.
| Situation | Likely next check | Decision boundary |
|---|---|---|
| The strip result is outside the listed 400 to 7,000 ppm range | Retest with a suitable method or ask for service support | The strip range may not cover the sample value. |
| The strip reads within range but the generator alarms | Confirm the generator model, manual target, and display message | A strip range is not the same as the generator's operating target. |
| Salt looks acceptable, but sanitizer or pH is off | Adjust water treatment according to the appropriate sanitizer and pH test results | Salt ppm does not replace disinfectant and pH checks. |
| The reading changed sharply after adding salt or water | Allow proper circulation according to pool-service practice and retest before adding more | A single immediate reading can lead to overcorrection. |
Reliable salt-strip reading depends on using the right strip, the right chart, and the right comparison target.
Read salt test strips by keeping each number in its proper role.
Use the salt strip to measure sodium chloride ppm and respect the product's measurement range. Then compare that ppm with the salt chlorine generator's own target, not with a universal value. Finally, test sanitizer and pH separately before deciding whether the water is ready for use.
Most reading problems come from mixing up salt range, generator target, and sanitizer results.
No. CDC archived guidance listed free chlorine or bromine and pH checks separately, while a salt strip measures sodium chloride concentration.
No. For AQUA CHEM salt test strips, 400 to 7,000 ppm is the listed measurement range, not a universal operating target for every generator.
Retest with a fresh strip, confirm the conversion chart, and then compare both readings with the manual or service information for the exact generator model.
Not responsibly from the strip value alone. The customer also needs pool volume, current ppm, product-label directions, and the generator's model-specific target.
The AQUA CHEM page describes sodium chloride test strips for pools and hot tubs, including pools with salt generator systems.
Clear-looking water is not a substitute for testing. Check sanitizer and pH separately, and use the generator manual or a qualified service path for high-salt warnings.
No accuracy ranking is supported here. Choose strips with a range and chart suitable for your pool, and use comparative accuracy claims only when backed by reliable test data.